Watlow EZ-ZONE RMC Bedienungsanleitung PDF herunterladen (Seite 77)

Watlow EZ-ZONE

RMC Module • 74 • Chapter 4 Setup Page

RMC Module • Setup Page

Dis-

play

Parameter Name

Description

Range Default

Modbus

Relative

Address

CIP

Class

Instance

Attribute

hex (dec)

Probus

Index

Parameter

Data

Type

& Read/

Write

[`L;hy]

[ L.hy]

Limit (1 to 4)

Hysteresis

Set the hysteresis for

the limit function. This

determines how far into

the safe range the pro-

cess value must move

before the limit can be

cleared.

0.001 to 9,999.000°F or units

0.001 to 5,555.000°C

3.0°F or

units

2.0°C

722

[offset 30]

0x70 (112)

1 to 4

41 12002 float

RWES

[SP;Lh]

[SP.Lh]

Limit (1 to 4)

Set Point High Limit

Set the high end of the

limit set point range.

-1,999.000 to 9,999.000 9,999.000 736

[offset 30]

0x70 (112)

1 to 4

42 12009 float

RWES

[SP;Ll]

[SP.LL]

Limit (1 to 4)

Set Point Low Limit

Set the low end of the

limit set point range.

-1,999.000 to 9,999.000 -1,999.000 738

[offset 30]

0x70 (112)

1 to 4

0xA (10)

43 12010 float

RWES

[`Lh;S]

[ Lh.S]

Limit (1 to 4)

High Set Point **

Set the high process

value that will trigger

the limit.

-1,999.000 to 9,999.000°F or

units

-1,128.000 to 5,537.000°C

0.0°F or

units

-18.0°C

726

[offset 30]

0x70 (112)

1 to 4

39 12004 float

RWES

[`LL;S]

[ LL.S]

Limit (1 to 4)

Low Set Point **

Set the low process

value that will trigger

the limit.

-1,999.000 to 9,999.000°F or

units

-1,128.000 to 5,537.000°C

0.0°F or

units

-18.0°C

724

[offset 30]

0x70 (112)

1 to 4

38 12003 float

RWES

[SFn;A]

[SFn.A]

Limit (1 to 4)

Source Function A **

Set the source for the

limit reset function.

[nonE] None (61)

[`dio] Digital I/O (1142)

[`FUn] Function Key (1001)

[`uAr] Variable (245)

None 748

[offset 30]

0x70 (112)

1 to 4

0x0F (15)

- - - - 12015 uint

RWES

[`Si;A]

[ Si.A]

Limit (1 to 4)

Source Instance A **

Set the instance of the

function selected above.

1 to 250 1 - - - - 0x70 (112)

1 to 4

0x10 (16)

- - - - 12016 uint

RWES

[`S2;a]

[ SZ.A]

Control Loop (1 to 4)

Source Zone A **

Set the zone of the func-

tion selected above.

0 to 16 0 - - - - 0x6B

(107)

1 to 4

0x11 (17)

- - - - 12017 uint

RWES

[`lCr]

[ LCr]

Limit (1 to 4)

Limit Clear Request

Clear limit once limit

condition is safe.

Clear (0)

No Change (255)

- - - -

720

[offset 30]

0x70 (112)

1 to 4

- - - - 12001 uint

[`l;st]

[ L.St]

Limit (1 to 4)

Status **

Reflects whether or not

the limit is in a safe or

failed mode.

Fail (32)

Safe (1667)

- - - -

744

[offset 30]

0x70 (112)

1 to 4

0x0D (13)

- - - - 12013 uint

Note:

Some values will be rounded off to fit in the four-character display.

Full values can be read with other interfaces.

Note:

If there is only one instance of a menu, no submenus will appear.

** These parameters/prompts are available in these menus with firmware revisions 6.0 and

above.

R: Read

W: Write

E: EEPROM

S: User Set

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 ... 235 236

Kommentare zu diesen Handbüchern

Keine Kommentare

Watlow EZ-ZONE RMC Bedienungsanleitung Seite 77

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Watlow EZ-ZONE RMC