Watlow EZ-ZONE RMC Bedienungsanleitung Seite 223
- Seite / 236
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Watlow EZ-ZONE
®
RMC Module • 220 • Chapter 8 Appendix
Indication Description Possible Cause(s) Corrective Action
Remote User Inter-
face (RUI) menus
inaccessible
Unable to access [`SEt],
[OPEr], [FCty] or [ProF]
menus or particular prompts
in Home Page
• Security set to incorrect level
• Check [`loC] settings in Factory Page
• Enter appropriate password in [UloC]
setting in Factory Page
• Digital input set to lockout keypad • Change state of digital input
• Custom parameters incorrect • Change custom parameters in Factory
Page
RUI value to low
[ual;l]
Value to low to be displayed
in 4 digit LED display
<-1999
• Incorrect setup • Check scaling of source data
RUI value to high
[ual;h]
Value to high to be displayed
in 4 digit LED display
>9999
• Incorrect setup • Check scaling of source data
Detection of and Rules Around Abnormal Sensor Conditions
Inputs Detection of Abnormal Conditions
Thermocouple
Shorted No direct detection, Open loop firmware detection.
Open Yes, Parasitic pull-up
Reversed Yes, firmware detection
Current Source
Shorted Range limiting only
Open Range limiting only
Reversed Range limiting only
Voltage Source
Open Range limiting only
Shorted Range limiting only
Reversed Range limiting only
RTD
S1 open Yes, pulled up.
S2 open Not implemented.
S3 open Yes, pulled up.
S1 short to S2 Yes, pulled up
S1 short to S3 Yes, pulled down to under range.
S2 shorted to S3 Not implemented, Possible, monitor S2 voltage.
S1 and S2 open Yes, pulled down to under range.
S1 and S3 open Yes, S1 pulled up.
S2 and S3 open Yes pulled up.
Thermistor
S1 open Yes, pulled up to sensor over range.
S3 open Yes, pulled up to sensor over range.
S1 short to S3 Yes, pulled down to sensor under range.
S1 and S3 open Yes, S1 pulled up to sensor over range.
- User’s Guide 1
- RMC (Control) Module 1
- Control Module 1
- Safety Information 2
- Warranty 2
- Technical Assistance 2
- Table of Contents 4
- Table of Contents (cont.) 5
- Chapter 1: Overview 7
- Introduction 8
- • 6 • Chapter 1 Overview 9
- Getting Started Quickly 10
- Functions 10
- Function 11
- Slot CSlot C 12
- Module Orientation 13
- Chapter 2: Install and Wire 16
- Dimensions 17
- Power Supplies 18
- Modular Backplane Connector 19
- Module Installation 19
- Removal of the Modular Back 20
- Module Removal 20
- Power and Communications 22
- RMC Module Isolation Diagram 24
- Slot A, B, D, E 25
- RMC Part # Digits 4, 6, 8, 10 26
- RMC Part # Digit 11 is C 28
- Output 2, 4, 6, 8 Switched DC 30
- Safe Operating Area 33
- A Network Using Modbus RTU 38
- Connecting the Modules 39
- [``o;u] Output Value 42
- [`Ain] Value ** 63
- [`Set] Timer Menu 64
- Offset the input reading 68
- 0x68 (104) 68
- 0x70 (112) 76
- Set an offset value for a 87
- 0x80 (128) 95
- 0x83 (131) 95
- 0x82 (130) 100
- 0x7F (127) 100
- Watlow EZ-ZONE 110
- 0x87 (135) 116
- On (63) 119
- Profiling Parameters 131
- [`Pro] Process 148
- Change this value to 152
- Chapter 7: Features 154
- Chapter 7: Features (cont.) 155
- Tuning the PID Parameters 156
- Autotuning with TRU-TUNE+ 157
- Before Tuning 157
- How to Autotune a Loop 157
- • 155 • Chapter 7 Features 158
- • 156 • Chapter 7 Features 159
- Temperature 160
- Control Methods 161
- On-Off Control 162
- Proportional (P) Control 163
- Dead Band 163
- Variable Time Base 164
- Single Set Point Ramping 164
- Cascade Control 165
- Compressor Control 165
- Differential Control 165
- Input 1 Output 1 166
- Resetting a Tripped Limit 167
- Open Loop Detection 168
- Programming the EZ Key/s 168
- Current Sensing 168
- Using Password Security 169
- • 167 • Chapter 7 Features 170
- • 168 • Chapter 7 Features 171
- Software Configuration 172
- • 170 • Chapter 7 Features 173
- • 171 • Chapter 7 Features 174
- Function Block Descriptions 175
- Analog Input Function 176
- -1,999.000 to 9,999.000 176
- Overview 177
- Control Function 179
- Counter Function 181
- Custom Function 181
- Diagnostic Function 181
- Digital Input/Output Function 182
- Global Function 182
- Math Function 187
- Switch Over 189
- Multiply 190
- Absolute Difference 191
- Range Low 193
- Profile Function 194
- Profiling 197
- Unused Step Type 197
- Time Step Type 198
- Rate Step Type 199
- Soak Step Type 200
- State Step Type 201
- Jump Step Type 203
- Wait Time 204
- Subroutine Step Type 205
- End Step Type 206
- Process Value Function 207
- Output Value 207
- Process Value 208
- Setting 212
- Timer Function 214
- One Shot 217
- Retentive 218
- Variable 219
- Chapter 8: Appendix 220
- • 221 • Chapter 8 Appendix 224
- Control Module Specifications 227
- Digital Input 228
- Dry Contact 228
- Output Hardware 229
- Output Hardware (cont.) 229
- • 228 • Chapter 8 Appendix 231
- • 229 • Chapter 8 Appendix 232
- • 230 • Chapter 8 Appendix 233
- • 231 • Chapter 8 Appendix 234
- EZ Zone Series RM 235
- How to Reach Us 236
Verwandte Produkte und Handbücher für Sensoren Watlow EZ-ZONE RMC
Sensoren Watlow EZ-ZONE RME Bedienungsanleitung
(112 Seiten)
(112 Seiten)
Sensoren Watlow EZ-ZONE RME Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Sensoren Watlow EZ-ZONE RME Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Sensoren Watlow EZ-ZONE RMC Bedienungsanleitung
(213 Seiten)
(213 Seiten)
Sensoren Watlow EZ-ZONE RME Bedienungsanleitung
(113 Seiten)
(113 Seiten)
Sensoren Watlow EZ-ZONE RME Bedienungsanleitung
(115 Seiten)
(115 Seiten)
Sensoren Watlow EZ-ZONE RME Bedienungsanleitung
(112 Seiten)
(112 Seiten)
Sensoren Watlow EZ-ZONE RMH Bedienungsanleitung
(161 Seiten)
(161 Seiten)
Sensoren Watlow EZ-ZONE RMH Bedienungsanleitung
(149 Seiten)
(149 Seiten)
Sensoren Watlow EZ-ZONE RMH Bedienungsanleitung
(149 Seiten)
(149 Seiten)
Sensoren Watlow EZ-ZONE RMH Bedienungsanleitung
(157 Seiten)
(157 Seiten)
Sensoren Watlow EZ-ZONE ST Bedienungsanleitung
(66 Seiten)
(66 Seiten)
Sensoren Watlow EZ-ZONE ST Bedienungsanleitung
(97 Seiten)
(97 Seiten)
Sensoren Watlow EZ-ZONE ST Bedienungsanleitung
(133 Seiten)
(133 Seiten)
Sensoren Watlow MICRODIN Bedienungsanleitung
(24 Seiten)
(24 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern