Watlow EZ-ZONE RME Bedienungsanleitung PDF herunterladen (Seite 52)

Watlow EZ-ZONE

RME Module • 49 • Chapter 4 Setup Page

RME Module • Setup Page

Dis-

play

Parameter Name

Description

Range Default

Modbus

Relative

Address

CIP

Class

Instance

Attribute

hex (dec)

Profibus

Index

Param-

eter

Data

Type

Read/

Write

[`A;Si]

[ A.Si]

Alarm (1 to 8)

Silencing

Turn alarm silencing on to

allow the user to disable

this alarm.

[`oFF] Off (62)

[``on] On (63)

Off 1450

[offset 60]

0x6D (109)

1 to 8

11 9006 uint

RWES

[A;dSP]

[A.dSP]

Alarm (1 to 8)

Display

Display an alarm message

when an alarm is active.

[`oFF] Off (62)

[``on] On (63)

On 1470

[offset 60]

0x6D (109)

1 to 8

0x10 (16)

12 9016 uint

RWES

[`A;dL]

[ A.dL]

Alarm (1 to 8)

Delay

Set the span of time that

the alarm will be delayed

after the process value ex-

ceeds the alarm set point.

0 to 9,999 seconds 0 1480

[offset 60]

0x6D (109)

1 to 8

0x15 (21)

13 9021 uint

RWES

[a;Clr]

[A.CLr]

Alarm (1 to 8)

Alarm Clear Request **

Write to this register to

clear an alarm

0 - - - - 1490

[offset 60]

0x6D

(109)

1 to 8

0xD (13)

14 9013

uint

[A;sir]

[A.Sir]

Alarm (1 to 8)

Alarm Silence Request

Write to this register to

silence an alarm

0 - - - - 1492

[offset 60]

0x6D

(109)

1 to 8

0xE (14)

15 9014

uint

[`a;st]

[ A.St]

Alarm (1 to 8)

Alarm State **

Current state of alarm

Startup (88)

None (61)

Blocked (12)

Alarm low (8)

Alarm high (7)

Error (28)

- - - - 1456

[offset 60]

0x6D

(109)

1 to 8

- - - - 9009 uint

[CUrr]

[`Set]

Current Menu

[`C;Sd]

[ C.Sd]

Current (1 to 4)

Sides

Use Current Sides to select

which side of the current to

monitor.

[`oFF] Off (62)

[high] High (37)

[low] Low (53)

[both] Both (13)

off 1088

[offset 50]

0x73 (115)

1 to 4

145 15005 uint

RWES

[`C;Ur]

[ C.Ur]

Current (1 to 4)

Read Enable

Use Current Read Enable

to display solid-state relay

(SSR) failure and heater

failure messages on the

RUI (remote user inter-

face).

[``no] No (59)

[`yes] Yes (106)

no 1086

[offset 50]

0x73 (115)

1 to 4

146 15004 uint

RWES

[`C;dt]

[ C.dt]

Current (1 to 4)

Detection Threshold

Current Detection Thresh-

old is for factory use only.

3 to 59 9 1102

[offset 50]

0x73 (115)

1 to 4

0xC (12)

147 15012 uint

RWES

Note:

Some values will be rounded off to fit in the four-character display. Full values can be read

with other interfaces.

Note:

If there is only one instance of a menu, no submenus will appear.

** These parameters/prompts are available in these menus with firmware revisions 6.0 and

above.

R: Read

W: Write

E: EEPROM

S: User Set

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 123 124

Kommentare zu diesen Handbüchern

Keine Kommentare

Watlow EZ-ZONE RME Bedienungsanleitung Seite 52

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Watlow EZ-ZONE RME