Watlow Series SD PID Profiling Controller Bedienungsanleitung PDF herunterladen (Seite 59)

Watlow Series SD • 57 • Chapter 10 Profiling

Display Parameter Name

Description

Settings Range

(Integer values for Modbus

in parentheses.)

Default Modbus*

(less 40,001

offset)

Read/Write

Appears if:

N/A File Running

File number that is currently running.

1 to 4 1 900 R Profile is running.

N/A

Step Running

Step number that is currently running.

1 to 10 1 901 R Profile is running.

[EnSP]

End Set Point Value

Set point value reached at the end of the

current step.

[sp;lo] to [sphi]

*902, 903 R Profile is running.

[hour]

Hours Remaining

Indicates number of hours remaining in

the step currently running.

0 to 99 904 R Profile is running.

Active if the value

set for [ptyp] is

[``ti] or time

based profiles.

[Min]

[~Min]

Minutes Remaining

Indicates number of minutes remaining

in the step currently running.

0 to 59 905 R Profile is running.

Active if the value

set for [ptyp] is

[``ti] or time

based profiles.

[`SEc]

[ SEc]

Seconds Remaining

Indicates number of seconds remaining

in the step currently running.

0 to 59 907 R Profile is running.

Active if the value

set for [ptyp] is

[``ti] or time

based profiles.

[rAte]

[rAtE]

Ramp Rate

Rate at which the profile changes in de-

grees or units per minute.

0.0 to 9999.9 (0 to

9999900)

*907, 908 R Profile is running.

Active if the value

set for [ptyp] is

[rate] or rate

based profiles.

[Ent1]

Event Output 1 status

Indicates Event Output 1 status.

[`Off] (0)

[``On] (1)

909 R Profile is running.

Output 1 is set to

[Ent1].

[Ent2]

Event Output 2 status

Indicates Event Output 2 status.

[`Off] (0)

[``On] (1)

910 R Profile is running.

Output 2 is set to

[Ent2].

[Ent3]

Event Output 3 status

Indicates Event Output 3 status.

[`Off] (0)

[``On] (1)

911 R Profile is running.

Output 3 is set to

[Ent3]

[WPr]

Wait-for Process Value

Profile clock waits until the process value

matches the Wait-for value and then con-

tinues with the step.

[sp;lo] to [sphi]

*912, 913 R Profile is run-

ning. [WF;P] set to

[~YEs].

[`EJC]

[ EJC]

Elapsed Jump Count

Number of times the profile has been

through the Jump Loop Step.

0 to 9999 (0 to 9999000) 914 R Profile is running

and the current

profile step running

is a Jump Loop Step

Type.

N/A Failed File Number

Indicates the file number that failed the

Pre-Run check.

1 to 4 365 R Profile State is set

to 3 (Pre-Run Failed

Start) or 4 (Pre-Run

Failed Resume)

N/A Failed Step Number

Indicates the step number that failed the

Pre-Run check.

1 to 10 366 R Profile State is set

to 3 (Pre-Run Failed

Start) or 4 (Pre-Run

Failed Resume)

Note: Some values will be rounded off to fit in the four-character display. Full values can be read with Modbus. All temperature pa-

rameters are in °F through Modbus.

* Low register numbers contain the two higher bytes; high register numbers contain the two lower bytes of the four-byte integer.

Decimal precision is implied at three decimal places unless otherwise noted.

Monitoring Profile Status from Modbus

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 87 88

Kommentare zu diesen Handbüchern

Keine Kommentare

Watlow Series SD PID Profiling Controller Bedienungsanleitung Seite 59

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Watlow Series SD PID Profiling Controller