Watlow MICRODIN Bedienungsanleitung Seite 61
- Seite / 106
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Parameters
=Read Only; =Read/Write; =Turn On/Off Watlow MicroDIN 5.13
ON
PID Group
Monitor
PID Output Power ..................................... 5.13
Initiate Auto-tune ...................................... 5.14
Setup
Auto-tune Set Point .................................. 5.13
Proportional Band ..................................... 5.14
Integral ...................................................... 5.14
Reset ........................................................... 5.15
Derivative .................................................. 5.15
Rate ............................................................ 5.15
Cycle Time ................................................. 5.15
Control Output Hysteresis ....................... 5.16
PID Group – Monitor
PID Output Power
• Monitor the calculated PID power level. See Chapter 4 for
information about PID control.
• Read only
• Modbus: 204
Range
heat: 0.0 to 100.0
cool: -100.0 to 0.0
Default
none
Active
always
PID Group – Use
Auto-tune Set Point
• Set the auto-tune set point as a percent of the currently active set
point.
• Read/write
• Modbus: 304
Range
50 to 150
Default
90
Active
always
ç
CAUTION:
Avoid writing
continuously to
EEPROM memory.
Continuous writes
may result in
premature control
failure, system
downtime and
damage to
processes and
equipment.
See Disable Non-
volatile Memory
(System Group).
- MICRODIN 1
- User’s Manual 1
- Addendum 2
- Declaration of Conformity 3
- Meet the MicroDIN Team 4
- Safety Information 5
- Technical Assistance 5
- Your Feedback 5
- Table of Contents 6
- Chapter One: 7
- Setup Steps 9
- Indicator Lights 9
- Overview 10
- Chapter Two: 11
- Communications Setup 11
- Communications Overview 12
- EIA-485 Network 13
- Communication 14
- MicroDIN, A Modbus 15
- Remote Terminal Unit (RTU) 15
- Modbus Register Numbers 16
- Set Address/Baud Rate 17
- C D D C 18
- 8 None 1 1 19
- Chapter Three: 21
- Installation and Wiring 21
- Introduction 22
- Mounting the MicroDIN 23
- Figure 3.3 23
- Install and Wire 24
- To Mount MicroDIN 24
- To Dismount MicroDIN 24
- Input Wiring 26
- Output and Power Wiring 27
- Communications Wiring 28
- Wiring Examples 30
- Chapter Four: 33
- Features 33
- The System 34
- Power Limit 35
- Calibration Offset 36
- Filter Time Constant 37
- Sensor Selection 38
- Range Low and Range High 38
- Control Methods 39
- Proportional Control 40
- Alarm Set Points 43
- Alarm Hysteresis 43
- Process or Deviation Alarms 44
- Alarm Latching 44
- Alarm Silencing 45
- Panel Indicator Lights 46
- Open Loop Detect 46
- Bumpless Transfer 47
- Chapter Five 49
- Learn the Parameters 49
- System Group 50
- System Group continued 51
- Input Group 52
- Input Group continued 53
- Control Output Group 56
- Parameters 57
- Power Limit Set Point 57
- High Side Power 57
- Low Side Power 58
- Fixed Manual Output 58
- Operation Group 59
- Operation Group continued 60
- PID Group 61
- PID Group continued 62
- Alarm Output Group continued 66
- Error Group continued 70
- Characteristics Group 73
- Serial Number 2 74
- Software ID Number 74
- Software Revision 74
- Diagnostics Group continued 75
- Calibration Group continued 78
- Chapter Six: 81
- Operation and Calibration 81
- MicroDIN Startup 82
- MicroDIN Shutdown 83
- Operations 84
- • See p. 5.6 85
- Equipment Required 86
- Setup and calibration 86
- Appendix 87
- Writing a Modbus Application 88
- Packet Syntax 88
- Loop Back Command (0x08) 91
- Exception Responses 92
- Glossary 94
- Output #1: User selectable 99
- Output #2: User selectable 99
- A.14 Watlow MicroDIN 100
- Ordering Information 101
- 4.4, 5.6 102
- Watlow MicroDIN A.17 103
- Parameter Index 104
- Statement: 106
- Quality and 106
Verwandte Produkte und Handbücher für Sensoren Watlow MICRODIN
Sensoren Watlow LogicPro Bedienungsanleitung
(296 Seiten)
(296 Seiten)
Sensoren Watlow MLS Bedienungsanleitung
(142 Seiten)
(142 Seiten)
Sensoren Watlow Power Series Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Watlow Power Series Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Watlow Power Series Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Sensoren Watlow Power Series Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Sensoren Watlow Power Series Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Watlow Power Series Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Sensoren Watlow QPAC Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Sensoren Watlow SBL Card Bedienungsanleitung
(2 Seiten)
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern