Watlow CAS Bedienungsanleitung Seite 14
- Seite / 98
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4 CAS User’s Guide
Introduction
Voltage inputs: 0-12V, 0-10V, 0-5V, 0-1V, 0-500mV, 0-100 mV with
scaling resistors.
Source Impedance: for 0-60 mV, measurements are within
specification with up to 500 ohms source resistance.
Digital Inputs
Number: 8
Configuration: 8 selectable for remote job selection. Digital input #8 is
only used for external alarm acknowledge.
Input Voltage Protection: Diodes to supply and common. The source
must limit current to 10 mA for override conditions.
Voltage Levels: <1.3V=Low; >3.7V=High (TTL).
Maximum Switch Resistance to Pull Input Low: 1 Kohms.
Minimum Switch Off Resistance: 11 Kohms.
Digital Outputs
Number: 34
Operation: Open collector output; On state sinks to
logic common.
≤
20 mA for 35 outputs,
≤
40 mA for a single output,
Ι
Total
≤
700 mA.
Function: Selectable as alarm latched/unlatched.
Off State Leakage Current: <.01 mA to DC common.
System Digital Outputs
System Digital Outputs: 1 Global Alarm, 1 CPU watchdog.
Operation: Open collector output; On state sinks to logic common.
≤
20
mA for 35 outputs,
≤
40 mA for a single output,
Ι
Total
≤
700 mA.
Range Input Resistance
0-12 V 85K ohms
0-10 V 50 K ohms
0-5 V 40 K ohms
0-1 V 7.4 K ohms
0-500mV 6.2 K ohms
0-100 mV 1.2 K ohms
0-20 mA 3 ohms
0-10 mA 6 ohms
- User ’s Guide 1
- Warranty 2
- Contents 3
- CAS User’s Guide iii 5
- Overview 7
- System Diagram 8
- Parts List 8
- 10
- Introduction 11
- Specifications 13
- Digital Inputs 14
- Digital Outputs 14
- System Digital Outputs 14
- Miscellaneous Specifications 15
- 6 CAS User’s Guide 16
- Installation 17
- Precautions and Warnings 18
- Recommended Tools 19
- CAS Mounting Procedure 20
- TB-50 Mounting Instructions 21
- Grounding 24
- Thermocouple Wiring 24
- Input Wiring 24
- Communications Wiring 25
- Wiring: Noise Suppression 26
- General Wiring 27
- Connections Test 28
- Wiring Outputs 29
- Using the Cable Tie Wraps 30
- Alarm Output Connections 31
- Watchdog Timer 31
- TB-50 Connections 32
- Input Scaling 33
- Scaling Values 34
- Scaling and Calibration 35
- T/C Inputs 36
- Connecting Thermocouples 36
- Current Inputs 36
- Voltage Inputs 37
- Unused Inputs 37
- Serial Communications 38
- JU 1JU 1 39
- Configuring Communications 40
- Recommended Wire Gauges 41
- 32 CAS User’s Guide 42
- Using the CAS 43
- Front Panel 44
- Single Channel Display 46
- Job Display 47
- Change Setpoint 48
- Acknowledging an Alarm 49
- Resetting an Alarm 49
- 40 CAS User’s Guide 50
- How to Enter the Setup Menus 51
- How to Edit a Menu 51
- CAS Menus 52
- Setup Global Parameters Menu 53
- Save Setup to Job 54
- Job Select Inputs 54
- Job Select Input Polarity 55
- Startup Alarm Delay 55
- Keyboard Lock Status 56
- Scanner Address 56
- Communications Error Checking 56
- Communications Baud Rate 57
- Allen-Bradley Protocol 57
- AC Line Frequency 57
- Digital Output Polarity 58
- EPROM Information 58
- Setup Channel Inputs 59
- Pulse Sample Time 60
- Channel Name 60
- Input Units 61
- Input Reading Offset 61
- Linear Scaling Menus 62
- Variable 63
- InputR eading 63
- Display Format 64
- High Process Value 64
- High Reading 65
- Low Process Value 65
- Low Reading 66
- Input Filter 66
- Setup Channel Alarms 67
- Alarm Delay 69
- High Process Alarm Setpoint 69
- High Process Alarm Type 69
- Deviation Alarm Value 70
- High Deviation Alarm Type 70
- Low Deviation Alarm Type 71
- Low Process Alarm Setpoint 72
- Low Process Alarm Type 72
- Alarm Deadband 73
- Manual I/O Test 75
- Digital Output Test 76
- Keypad Test 76
- Troubleshooting 77
- Manual System Reset 78
- Returning the Unit 78
- TB-50 Test 79
- Checking an Analog Input 79
- Checking Digital I/O 79
- Digital Input Test 80
- Computer Problems 81
- Ground Loops 82
- Software Problems 82
- User-Written Software 82
- Changing the EPROM 83
- Appendix: Linear Scaling 85
- Examples 85
- Example 2 86
- Example 3 87
- 78 CAS User’s Guide 88
- Glossary 89
- 88 CAS User’s Guide 98
Verwandte Produkte und Handbücher für Sensoren Watlow CAS
Sensoren Watlow CLS Bedienungsanleitung
(180 Seiten)
(180 Seiten)
Sensoren Watlow CLS200 Bedienungsanleitung
(251 Seiten)
(251 Seiten)
(2 Seiten)
(2 Seiten)
(2 Seiten)
Sensoren Watlow CPC400 Bedienungsanleitung
(230 Seiten)
(230 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern