Watlow Series F4P Bedienungsanleitung Seite 21
- Seite / 124
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Watlow Series F4P Factory Page ■ 5.1
Chapter Five: Factory Page
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.1
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.3
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.3
5
Security
The Series F4P allows users to set separate security
levels for the Static Set Point prompt on the Main Page,
for all menus on the Operations Page, as well as for the
Setup Page and Factory Page. Four levels of security are
available:
• Full Access (operators can enter and change
settings);
• Read Only (operators can read but not change
settings);
• Password (operators can enter and change settings
after entering a password); and
• Hidden (operators cannot see the menu or page — it
is not displayed). Set Point settings cannot be
Hidden.
✔ Note: Full Access is the default for all menus. Unless
you change the level of access, operators will be able to
read and change every setting in every menu in the
Series F4P software.
How to Set Lockout Levels
Using the Lockout Menu, you can limit access to the
following menus and pages:
• Set Point on Main Page
• Operations Page Autotune PID
• Operations Page Edit PID
• Operations Page Alarm Set Point
• Setup Page
• Factory Page
Choose the item to lock out, press .. and choose the level
of access: Full, Read Only, Password or Hidden. If you
choose Password, you must set the password — see
below.
✔ Note: For more information about how parameter
settings affect the controller’s operation, see the Features
Chapter.
ç CAUTION: Only authorized and qualified personnel
should be allowed to perform preventive and corrective
maintenance on this unit.
…Lock>Autotune PID___
Full Access
Read Only
>Password
.
…Factory>Set Lock___
Set Point
>Oper. Autotune PID ■
Oper. Edit PID ▼
.
Main>Factory________
>Set Lockout
Diagnostic
Test
- User’s Manual 1
- Series F4P 1
- Safety Information 2
- Technical Assistance 2
- Your Comments 2
- Series F4P: Table of Contents 3
- Chapter One: Introduction 5
- Setup Steps 6
- How to do itWhat to do 6
- Chapter Two: Navigation and 7
- Keys, Displays and Lights 8
- Static Set Point Control 9
- Troubleshooting 10
- Alarm Set Points 15
- To Clear an Alarm or Error 15
- Edit PID 16
- Multiple PID Sets 17
- Chapter Four: Setup Page 19
- Customizing the Main Page 20
- Static Messages 20
- Chapter Five: Factory Page 21
- Enter a Password 22
- Use a Password 22
- Change a Password 22
- Diagnostics 23
- Calibration 23
- Process Output Procedure 25
- Retransmit Output Procedure 26
- Chapter Six: Parameters 27
- Main Page Parameters 28
- Register 29
- Operations Page Parameters 30
- Chapter 31
- Ramp to Set Point 33
- PID Crossover 33
- Control Set Points 34
- Remote/Local Set Points 35
- Setup Page Parameters 37
- Analog Input x (1 to 3) 38
- Analog Input 2 39
- Analog Input 3 41
- Digital Input x (1 to 4) 43
- Control Output x (1A and 1B) 44
- Alarm Output x (1 and 2) 45
- Communications 46
- Retransmit Output x (1 and 2) 46
- Custom Main Page 47
- Static Message 48
- Process Display 48
- Setup Page Parameter Record 49
- Factory Page Parameters 52
- Diagnostic 53
- Calibrate Input x (1 to 3) 55
- Chapter Seven: Features 59
- Temperature 60
- High Scale and Low Scale 62
- Digital Inputs 62
- Control Methods 63
- On-Off Control 64
- Proportional Control 64
- Dead Band 65
- Al R i h H i 69
- Advanced Features 70
- Digital Set Points 72
- Features in the 73
- Enhanced Series F4P 73
- Controller 73
- Curve A (PID) 74
- Curve B (Cascade) 74
- Curve C (Single-control) 74
- Differential Control 75
- Ratio Control 75
- Dimensions 79
- Panel Dimensions 80
- Wiring the Series F4P 83
- Thermocouple 84
- 0-20mA or 4-20mA Process 84
- 0 to 50mV 84
- Inputs x (2 and 3) 85
- Digital Inputs x (1 to 4) 87
- Outputs 1A and 1B 88
- Outputs 1A and 1B (continued) 89
- Retransmit and Alarm Output 89
- Communications Wiring 90
- ICS Model 4899 91
- EIA-232 or 91
- Wiring Example 92
- Wiring Notes 93
- Chapter Nine: Communications 95
- Series F4P Modbus Registers 96
- For more informa 99
- 606 Decimal, Analog Input 1 105
- 616 Decimal, Analog Input 2 106
- 626 Decimal, Analog Input 3 106
- Appendix 109
- Specifications 110
- Ordering Information (2330) 111
- Series F4 112
- Glossary 113
- Series F4P Software Map 121
- Setup Page see Chapter 4 122
- Factory Page see Chapter 5 122
- About Watlow Winona 123
- Warranty 123
- How to Reach Us 124
Verwandte Produkte und Handbücher für Sensoren Watlow Series F4P
Sensoren Watlow Series F4P Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Sensoren Watlow Series F4P Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Sensoren Watlow Series F4P Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Sensoren Watlow Series F4S/D Bedienungsanleitung
(152 Seiten)
(152 Seiten)
Sensoren Watlow Series F4S/D Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Sensoren Watlow Series PD Bedienungsanleitung
(188 Seiten)
(188 Seiten)
Sensoren Watlow Series V4 Bedienungsanleitung
(21 Seiten)
(21 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern