Watlow 8LS Controller Bedienungsanleitung Seite 81
- Seite / 140
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Setup
8LS User’s Guide 73
Test I/O
The Test I/O main menu lets you view menus which can help you test
the digital inputs and the digital outputs.
The main menu looks like this:
Answering Yes to this prompt gets you into the I/O test submenus.
Below is the menu tree. Notice the default values in the boxes.
Digital Input Testing
Use this view-only menu to see the logic state of the 12 digital inputs as
1’s (High) or 0’s (Low). the menu displays inputs 1 through 12.
1234 56 78
LOOP PROCESS UNITS
ALARM SETPOINT STATUS OUTPUT%
TEST
I/O ?
Test
I/O?
Ins=1111
11111111
Test out
NR? 27
Dig out
NR27? On
1234 56 78
LOOP PROCESS UNITS
ALARM
SETPOINT STATUS OUTPUT%
INS = 1 1 1 1
1 1 1 1 1 1 1 1
Input 12
Input 9
Input 8Input 1
- User’s Guide 1
- Warranty 2
- Contents 3
- Using the 8LS 37 4
- Setup 45 4
- Tuning and Control 75 5
- Troubleshooting 85 6
- Appendix A: Ramp Soak 89 6
- Appendix B: 8LS-CP 105 7
- Appendix C: 8LS Cascade 121 7
- Glossary 123 7
- System Diagram 10
- 4 8LS User’s Guide 12
- Overview 12
- Introduction 13
- Installation 17
- Read This Before Installation 18
- Mounting The 8LS 19
- 12 8LS User’s Guide 20
- External Wiring 21
- General Wiring Requirements 21
- Cable Recommendations 23
- Noise Suppression 24
- 130 VAC ratin 25
- RTB Connections 27
- Analog Inputs 28
- Common Mode Voltage 28
- Normal Mode Voltage 28
- Grounding 28
- Input Scaling 29
- Resistor Installation 30
- Voltage Inputs 31
- Milliamp Inputs 31
- Thermocouple Inputs 31
- RTD Inputs 32
- Pulse Input 33
- Carbon Probe Input 33
- Control Outputs 35
- Pid Control Relay Outputs 36
- Primary Analog Outputs 37
- CPU Dip Switch 39
- RS-232 Connections 41
- RS-485 Description 42
- RS-485 Connections 43
- Using the 8LS 45
- Ramp/Soak 47
- Man/Auto 47
- Displays 48
- Single Loop Display 49
- Scanning Display 49
- Alarm Display 49
- SP ? 25 51
- 6 = AUTO 51
- SET? TUNE 51
- 6 SET MAN 52
- How to enter the Setup menus? 53
- How to edit a menu? 53
- (T/C & RTDs) 54
- 1 1 1 1 1 1 1 1 54
- GLOBALS? 55
- Save as Job 56
- Restore a Job 56
- Set Alarm Delay 56
- Set R/S Time Base 57
- Lock Panel 57
- Power Up Output Status 57
- CONTRLLR 58
- ADDR? 1 58
- COMM ERR 58
- CHK? BCC 58
- Communication Baud Rate 59
- Communication Protocol 59
- AC Line Frequency 59
- EPROM Version 60
- 1 SETUP 61
- INPUT? 61
- 1 INPUT 62
- TYPE? J 62
- 1 INPUT 63
- SMPLT? 1 63
- 1 INPUT 63
- UNIT = F 63
- Linear Scaling Menus 64
- High PV Display 64
- High RDG Display 64
- Low PV Display 64
- 1 LO RDG 65
- 1 OFFSET 66
- 1 SETUP 67
- CONTROL ? 67
- Heat/Cool PB 68
- Heat/Cool TI 68
- Heat/Cool TD 68
- Heat/Cool Output Filter 68
- 1 CONTROL 69
- SPR? 10 69
- OUTPUTS? 70
- 1 OUTPUTS 71
- CT ? 10 71
- ACT ?REV 72
- LIM ? 100 72
- LTM ? C 73
- NLO ?OFF 73
- 1 HT OUT? 74
- TERM BLK 74
- Setup Alarms 75
- Alarm Types 76
- Global Alarms 76
- Process Alarms 76
- High Process Alarm Setpoint 77
- High Process Alarm Status 77
- Deviation Band Alarm 78
- Deviation Band Alarm Status 78
- Low Process Alarm Setpoint 79
- Low Process Alarm Status 79
- Alarm Deadband 80
- Alarm Delay 80
- INS = 1 1 1 1 81
- TEST OUT 82
- NR = 1 82
- DIG OUT 82
- NR01? OFF 82
- Tuning and Control 83
- Control Modes 84
- Digital Output Control Forms 86
- Time Proportioning (TP) 86
- Output Digital Filter 87
- Reverse and Direct Action 87
- Integral Term (TI) Settings 89
- Derivative Term (TD) Settings 89
- Proportional Band Only (P) 90
- PI with Derivative (PID) 90
- 8LS User’s Guide 83 91
- 84 8LS User’s Guide 92
- Troubleshooting 93
- Computer Supervised Systems 94
- Communications Problems 95
- Serial Interface 95
- 88 8LS User’s Guide 96
- Appendix A: Ramp Soak 97
- Configuring Ramp/Soak 98
- Setting the R/S Time Base 99
- Editing R/S Parameters 99
- Choosing a Profile to Edit 99
- R/S PRO 100
- COPY? H 100
- A OUTTOL 100
- T? 1:00 100
- Editing the Ready Setpoint 101
- Editing a Segment 102
- Setting Segment Time 102
- A SEG 01 103
- SP? OFF 103
- EVENTS? 103
- Editing Event Outputs 104
- Changing Event States 104
- Editing Segment Triggers 104
- 1234 56 78 105
- Setting Segment Tolerance 106
- Ending a Profile 106
- Repeating a Profile 106
- 1 SELECT 107
- PROF? 0 107
- 1A00/20S 108
- SET? RUN 108
- 3 73 F 109
- 73 S 0 109
- Bar graph display 110
- Ramp/Soak Key Displays 110
- How long has the profile run? 110
- CYC 1/1 111
- SET?HOLD 111
- RESET? A 112
- Appendix B: 8LS-CP 113
- System Configuration 114
- Specifications 116
- CP Control 117
- Applications 118
- Carbon Probe 119
- Probe Burn Off 120
- Burn Off Function 121
- 1 INPUTS 122
- TYPE? K 122
- 2 INPUTS 122
- TYPE? CP 122
- CO+CO2% and % of Hydrogen 123
- Engineering Units 123
- 2 OFFSET 124
- ? 0 ºF 124
- 2 CP 124
- BURNOFF? 124
- Burn Off Time Interval 125
- Burn Off start Input 125
- Burn Off Time Period 126
- 2CP GAS 127
- OUTPN? 0 127
- 2 HIT %CP 127
- . 25 M 0 127
- 120 8LS User’s Guide 128
- Appendix C: 8LS Cascade 129
- Choosing the Primary Loop 130
- Glossary 131
- 132 8LS User’s Guide 140
Verwandte Produkte und Handbücher für Sensoren Watlow 8LS Controller
Sensoren Watlow ANASOFT Bedienungsanleitung
(95 Seiten)
(95 Seiten)
Sensoren Watlow ANAWIN 2 Bedienungsanleitung
(154 Seiten)
(154 Seiten)
Sensoren Watlow CAS200 Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Sensoren Watlow CAS Bedienungsanleitung
(98 Seiten)
(98 Seiten)
Sensoren Watlow CLS Bedienungsanleitung
(180 Seiten)
(180 Seiten)
Sensoren Watlow CLS200 Bedienungsanleitung
(251 Seiten)
(251 Seiten)
(2 Seiten)
(2 Seiten)
(2 Seiten)
Sensoren Watlow CPC400 Bedienungsanleitung
(230 Seiten)
(230 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern